Addressable
Single Loop Analogue Control Panel Expandable to 2 loops.
Category: Fire Alarm System
OCTO PLUS
Addressable
The OCTO+ Fire Alarm Control Panel is built on the pedigree of the worldwide known JUNO NET. Now featuring a fully peer-to-peer, multi-master networking solution. This new “CHAMELEON Network” solution enables extreme resilience in very large distributed systems.
On a CHAMELEON Network system, each network NODE+ has, in its internal configuration memory, the whole system information, i.e. in the unlikely event of a communication loss, there is no performance degradation of individual NODE+.
CHAMELEON REP
Addressable
The CHAMELEON REP is the best solution when you need full control of a networked system.
In a Chameleon Network, the CHAMELEON REPEATER is used as a “System Repeater”. It works as an addressed
networked panel (without loops) and has the ability to process and register (Event-log) all “system info”. For connection diagrams and project commissioning, please refer to the Chameleon Network manual as well as the manual of the Communication Interface being used.
The CHAMELEON REP is supplied without battery management capability. It is intended to be connected to an external power supply.The Cause and Effect programming of the whole system as well as all customer specific configuration can be downloaded or uploaded using the CHAMELEON CONNECTOR software and later broadcast to other networked panels (OCTO+, NODE+ and GEKKO).
CHAMELEON DISPLAY
Addressable
CHAMELEON DISPLAY should not be considered a fully featured SYSTEM repeater for Chameleon Networks.
The CHAMELEON DISPLAY, behaves as an extra display of the Master Panel display.
Non networked panels may need an remotely accessed extra display. In this situation, by applying an isolated CHAMELEON DISPLAY you will have a duplication of the panel Fascia. Everything displayed in the connected panel is then copied to the CHAMELEON DISPLAY. Every key press action is assumed as if the input was actually occurring on the connected panel. For connection diagrams and project commissioning, please refer to the Chameleon Network manual as well as the manual of the Communication Interface being used.
This solution is ideally for stand-alone panels. It is only possible to have one display connected per Chameleon connection available on panel. On networked systems, where the panel chameleon connections are most needed, it is recommended the use of CHAMELEON MINI REP system repeaters.
Compatible with GEKKO, OCTO+ and NODE+ range of panels.
ORION EX V2
Extinguishing
The ORION-EX V2 Conventional Fire Detection and Extinguishing Panel offers a creatively designed and aesthetically pleasing solution to satisfy the growing demand for dependable Fire Detection & Suppression Systems.
The ORION-EX V2 is designed and manufactured to comply with EN54-2, EN54-4 and EN12094-1 standards. The outstanding programmable features included in this panel are best suited to be installed in expensive housing areas and in general in all areas where loss of equipment can partially or totally disrupt the proper functioning of a business. Operation is extremely intuitive, offering simple control and one-button disablement facilities, as well as the one man test mode which provides simple and efficient testing of the system.
Advanced configuration solutions include the following: programmable pre-release and discharge times, electrovalve and flow switch status indications, manual and abort remote activation. There are 4 normal fire detection zones. All inputs are fully monitored for both Fire, Activation and Fault Conditions.
ORION-EX V2 system is complemented with dedicated repeater panels, addressable interfaces, output expansion boards as well as manual & abort call-points for remote extinguishing cycle control.
ORION EX MINI REP V2
Extinguishing
The ORION EX MINI REP V2 will provide remote control and system display status from multiple locations to an ORION EX V2 based Fire Alarm System. All Fire, Fault, Test and Disabled conditions are displayed. User is able to control all functions at Access Levels 1 and 2. Access to Level 2 is via the same four digit code used on the ORION EX V2. Its reduced dimensions make it ideal for installation in reception areas or security booths where it would be impractical and unattractive to install a full size control panel. This repeater panel can be connected to the Main Panel using 4 different communication technologies: RS232, RS485, Fiber Optics and TCP/IP.
MPX LED
Accessories
Interface card that provides in any of GFE’s Analogue Addressable Fire Detection Panels a LED indication of Fire/Fault condition for each individual zone. The LED Red indicator will be ON when the zone is in Fire condition.
The module requires a connection to either JUNO NET or JUNIOR Panels via a 5 way flat cable fitted with polarised connectors. And it should be connected to the MPX output of either panel.
This module operates in three different modes.
J-NET QUART
Accessories
The J-NET-QUART chip should be installed on the JUNO NET Painel Main Board when panel is fitted with an internal and/or external printer and when panel is connected to GFE’s graphical software package ODYSSEY, 3rd party BMS systems or MODBUS via one of GFE’s J-NET-ADV-COMS interface boards.
J NET IP – Printer
Accessories
This 40 column internally mounted thermal printer provides a hardcopy of the JUNO-NET panel log containing all relevant events occurring in the system.
All events are date and time stamped and are backed by a 2000 events deep rolling log kept in the panel’s non-volatile memory.
Note: In order for the printer to work properly it is necessary that the J-NET-QUART chip be installed on the JUNO-NET Panel – Main Board. Please refer to the panel’s installation manual for full details.
GFE NET PRINTER
Accessories
The GFE-NET-PRINTER is an external thermal line printer which is used to obtain a hardcopy of all recorded events from a JUNIOR or JUNO NET panel. The GFE-NET-PRINTER can be connected either via the JUNO NET panel’s printer output or alternatively via the data loop using RS-232, RS-485, Fiber Optics or TCP/IP J-NET-INT interfaces. JUNIOR panels can only be connected via the data loop.
All recorded events are referenced by date and hour and saved in the panel’s NVRAM (non-volatile memory).
FLUSH FRAME
Accessories
Flush Frame for JUNO NET.
NODE
Addressable
The NODE allows expansion of the JUNO NET system in groups of 1 to 4 loops.
It can be supplied as a standalone unit or in an enclosed cabinet, which contains a 2,3 A PSU/ Charger unit and space for standby rechargeable batteries. One RS422/RS485, Fibre Optic or TCP/IP interface is required per cabinet to enable networking with the rest of the system.
Each NODE mainboard controls up to four Analogue Addressable Detection Loops via its own independent processor. In the event of communication failure with the main control unit, the NODE is capable of operating independently, detecting Fire/Fault events and activating connected sounders and internal relays.
JUNIOR MINI REP
Addressable
The JUNIOR MINI-REP will provide remote control, system status display and monitoring functions for any of GFE’s Analogue Addressable Fire Detection Panels.
All Fire, Fault, Test and Disabled conditions are displayed. User is able to control all functions at access Level’s 1, 2 (authorized user level) and 3 (installer/ programming level). It’s reduced dimensions make it ideal for installation in reception areas or security booths.
A maximum of 4 JUNIOR MINI-REP panels can be connected to a single Addressable Panel if powered directly from the Control Panel’s Auxiliary Supply Output.
It includes as standard an RS485 interface. This unit is also compatible with all of GFE’s standard data loop interfaces allowing the JUNIOR MINI-REP panel to be interfaced to both JUNIOR and JUNO NET addressable panels.
CHAMELEON NETWORK
Addressable
All Chameleon Network Panels should be tailored to the building/site requirements. The complete system should be designed to meet all applicable regulations. The installation must then be performed in accordance with the system design.
The manual not only clarifies the components and connections during installation, but will also assist in commissioning and maintenance.
ORION
Conventional
The ORION is a 2, 4 and 8 Zone microprocessor controlled conventional Fire Alarm Control Panel with all the functions necessary to control small and medium size fire detection installations. Advanced configuration solutions include the following: programmable delay timer, zones coincidence, one man test and non-latching zones. Finally all inputs are fully monitored for both Fire, Activation and Fault Conditions.
ORION PLUS
Conventional
The ORION-PLUS range of expandable conventional control panels offers an aesthetically pleasing and functional cabinet design for larger projects demanding ease of installation and commissioning, as well as simple operation, typical of conventional installations.
The unit can be expanded easily from 8 to 16 zones by installing additional modules with 4 zones. The range also includes two types of repeater.
The outstanding programming features included in this panel range exceed the possibilities of standard conventional panels, using a graphic LCD display and real time clock which permits the recording of events in a time stamped log.
Operation is intuitive, offering simple control and one-button disablement facilities, as well as a one man test routine, which provides a highly effective way to perform regular testing of the fire alarm system.
Advanced configuration interfacing includes RS232, RS422/485, Fibre Optic, GSM-GPRS and TCP/IP. All of the above making use of our own proprietary interfaces.
JUNIOR V4
Addressable
JUNIOR V4 is a single loop Analogue addressable control panel which can be expanded to 2 loops. It provides a cost effective solution for small to medium sized installations. The JUNIOR V4 can support up to 125 addressable devices on each loop which are compatible with major analogue addressable communications protocols.
Using Global Fire’s advanced communications mechanism, up to 32 individually addressed Loop sounders can be connected to each of the JUNIOR V4 detection Loops. The JUNIOR V4 also supports Shadow and Auxiliary Sounder/ Beacons together with GFE’s new VULCAN 2 addressable Sounder-Beacon-Isolator along with all other GFE Interface devices.
The panel is equipped with a backlit LCD display of 4 rows each with 40 characters to give clear textual indications of Fire/ Fault occurrences to the end user. There are also 16 Zone Fire LED indicators.
JUNO NET
JUNO NET is a powerful Analogue Addressable Fire Alarm Control System with networking capabilities that facilitate the configuration of complex Wide Area Fire Detection Systems.
Modular construction and distributed intelligence allow systems of up to 96 Loops to be constructed. With a high level of built-in redundancy and emergency back-up features, the JUNO NET is fully equipped to control the most complex installations.
Using its wide array of interfacing capabilities the JUNO NET is ideally placed to provide an efficient and effective solution to the logistics of protecting large institutions, Universities, Airports, industrial complexes etc. which may have many individual Fire Alarm systems but require central reporting and control can easily be accommodated by the advanced capabilities of the JUNO NET.
ORION MINI
Conventional
The ORION MINI one & two zones conventional control panel, offers a creatively designed and aesthetically pleasing solution for smaller cost-conscious projects demanding simplicity of operation.
The programmable features included in this panel are: programmable time delay and Day/Night mode.
Operation is extremely intuitive , offering simple control and one-button disablement facilities, as well as the one man test mode which provides simple and efficient testing of the system.
ORION MINI REP
The ORION MINI-REP V2 will provide remote control and system display status from multiple locations to an ORION based Fire Alarm System. All Fire, Fault, Test and Disabled conditions are displayed. User is able to control all functions at Access Levels 1 and 2. Access to Level 2 is via the same four digit code used on the ORION V2. Its reduced dimensions make it ideal for installation in reception areas or security booths where it would be impractical and unattractive to install a full size control panel. This repeater panel can be connected to the main panel using 4 different communication technologies: RS232, RS485, Fiber Optics and TCP/IP.
GEKKO
The GEKKO Fire Alarm Control Panel is the successor of the enormously popular GFE JUNIOR panel.
The GEKKO can have from 1 to 4 addressable loops. It is housed in a functional ABS plastic enclosure, with only two screws used to close and secure the lid.
The new graphic backlit LCD display can accommodate any type of custom characters or graphic symbols, allowing multi-language support, as well as pictorial and customisable elements.
JUNIOR REP
Compliant with EN54-2. Display and Control Functions are replicated and shown in the same manner as on any of GFE’s Intelligent Addressable Fire Detection Panel. Access to Levels 2 and 3 is via the same code as programmed or the associated panel.
This unit uses the same plastic enclosure as the JUNIOR V4 panel and is available in 2 colours: white and red. It includes as standard an RS485 interface.This unit is also compatible with all of GFE’s standard data loop interfaces allowing the JUNIOR REP panel to be interfaced to both JUNIOR and JUNO NET addressable panels using RS485, Fibre Optic or TCP/IP.
JUNO NET REP
The Juno Net Repeater Panel, J-NET-EN54-REP, fully replicates the control panel information and control facilities allowing multiple operating points within the system. The J-NET-EN54-REP communicates with the Master Control Panel via an RS422/RS485, Fibre Optic or TCP/IP network. Sub-Panels can be integrated into the repeater panel to allow the connection of up to 3 additional detection loops, per sub-panel, to the system.
J-NET-EN54-REP is ideal for multiple building complexes where display and control of the system is required in various locations. Depending on control panel loading, power for the J-NET-EN54-REP can be supplied from the control panel’s auxiliary power output, an external 24 Volt power supply or an optional complete built-in 24 V, 2,4 A or 5 A power supply unit. If a sub-panel is installed in the repeater housing, then a 5 A power supply unit is required.